Safe burner management for world's leading steel producer

The latest production technologies are the focus of the steel giant ArcelorMittal, the world's leading steel manufacturer.

Aim: to make their own production processes safer and more efficient. That's why burner monitoring of the furnaces was optimised in their downpipe cold rolling mill in the Belgian city of Ghent.

The focus: efficient, safe automation, including more efficient diagnostics. When converting the plant, ArcelorMittal opted for the all-around service package from the automation expert Pilz: their automation system PSS 4000 is used but that's not all – Pilz also assumed responsibility for implementing the conversion.

The cold rolling mill at ArcelorMittal in Ghent is used to refine steel coils (strip steel rolls) in accordance with customers’ requirements.

The production process for downpipes in the cold rolling mill is divided into five steps in total: pickling, cold rolling, annealing, tempering, and then finishing.

Before pickling there is a hot rolling process, during which an oxide layer forms on the steel plates. This must then be removed in the cold rolling mill during pickling before the steel plates can be further processed.

In the next step, cold rolling, the pickled, hot-rolled plate is cooled and then reduced to its required thickness through pressure and tension forces.

To enable the steel strip to be cold-formed it must first undergo heat treatment. This process is carried out in two bell annealing areas – i.e. in annealing furnaces for steel coils, where the steel strip remains for a while in a closed furnace – and in a continuous annealing and refinement plant, which the steel coil passes through relatively quickly, in contrast to the closed annealing chamber.

The steel coils that leave the bell annealing area are then tempered (special heat treatment for steel), improving the mechanical surface properties of the steel plate. In the final step, the strip steel rolls are packaged and are then ready for shipping to the customer.

Yves De Sloover is an engineer at the cold rolling mill at ArcelorMittal.

"Our department is responsible for maintaining the processes in this area. On the continuous annealing plant, we also look after the PLC controller and the burner setting. Our aim is to keep production running continuously. That includes constant optimisation of the furnace," he said.

One challenge was the frequent shutting down of the start-up burners, which ignite the main burners. So this stage of the process was one area of focus with regard to optimisation.

De Sloover explains:,"At the start of the process the furnace is heated up to 1200°C with an open flame. In total there are 50 main burners, which are fed by 30 start-up burners. When the temperature of the furnace drops below 760 C after a standstill, these main burners are always used to restart the furnace."

That's also prescribed in the standard. It's mandatory in accordance with DIN EN 746, the engineer adds.

In the past, the start-up burners were controlled via a module, while flame monitoring occurred via UV cells at ignition. If one UV cell was defective, the whole plant would stop and would need to be restarted.

Each restart would take at least 40 minutes because unburned gases containing nitrogen had to be expelled first. The defective UV cell also had to be replaced each time. That was a real game of hide and seek because you never knew which UV lamp had failed. As a result, the downtimes were considerable.

Troubleshooting was also inefficient: although the burner control module forwarded information about the gas and air supply and UV detectors to the PLC, the opportunities for analysis were limited and time-consuming.

"And we couldn't make any changes on the controller because it only acted as a black box, so it was only responsible for recording the data from the PLC signals," De Sloover explains.

So downtimes had to be drastically reduced.

"First we switched to ionisation instead of UV detectors. The second step was to replace the ‘old’ burner control module," said Ives De Sloover. The ‘replacement’ was the Pilz automation system for automation and safety, the PSS 4000.

The Belgian steel manufacturer already had positive memories of the German automation solution supplier from an earlier collaboration, "We had already installed a Pilz safety solution on another plant and were completely satisfied with the quality of the components, the service, and the support. We were already familiar with the automation system and thanks to its scalability it represents a forward-looking solution", says the engineer, reflecting back.

Pilz directed the whole procedure for converting the cold rolling mill. The blast furnace is divided into five zones, each with ten burners. Zone three was the first to be converted.

The first step was to document the specifications of the module that had been used previously. Pilz then transferred these design specifications to the automation system's PSSuniversal PLC controller.

The aim was a longer mission time and speedy, therefore adequate diagnostic options. So, efficient visualisation to display the status of the burner was installed alongside the PSSuniversal PLC in a new, designated control cabinet.

As the burners run through various steps and sequences in accordance with the standard and must meet certain conditions in doing so, the visualisation was designed to guarantee the operators’ ability to read this status on the display at a glance.

"Also, the flame is displayed graphically on all ten burners, and the sensor data from the burner controller is shown on the display, so it's now possible to react much more quickly when a value is too low at any point," says a delighted De Sloover.

Finally, in zones four and five, an additional control cabinet with two PSSuniversal PLC was installed for both zones. Their status can also be read on the display in zone three.

The PAS4000 software from the automation system PSS 4000 can be used to configure function blocks, which focus on specific application scenarios; in this case, the burner application.

With the burner management software package it is possible to implement programs to control various burner types simply and flexibly and to perform safety functions such as safety gate contacts, E-STOPs, and light curtains. The use of ready-made, certified function blocks for burner management not only simplifies installation but validation too.

What's more, numerous other function blocks are available in the software for the automation system. Ives De Sloover describes the benefits of the system and its software package in a nutshell: "A huge advantage of the automation system is that it allows applications to be implemented to meet customers’ specific needs."

Since the furnace was converted it has run virtually non-stop. For the engineers at ArcelorMittal this means: "a good night's sleep." That's because, "More than once we were here during the night, searching for a defective UV sensor. That's all in the past", says a relieved De Sloover.

"Today the plant runs without any major disruptions. Should there be a malfunction, we immediately know where to find the fault."

The PSS 4000 automation system stands for optimum interaction between hardware and software components, network devices, and real-time Ethernet.